Petroleum Test Instruments for Quality Control, Calibration and Analysis from Stanhope Seta

MultiFlash Family of Flash Point Testers

MULTIFLASH AUTOMATIC MULTI METHOD FLASH POINT TESTER
(PENSKY-MARTENS, ABEL, TAG, AND SMALL SCALE)

Multiflash is a universal fully automated instrument designed for testing the flash point of fuels, lubricating oils,solvents, chemicals, waste materials and many other substances.

The instrument comprises a universal base unit that houses the display, control and data acquisition functions, and a series of interchangeable modules that allow the implementation of the required standard test methods.

Multiflash is ruggedly designed to provide simple and reliable operation and is specifically engineered to ensure a very low cost of maintenance. Click on links to right for detailed information on each module.

Pensky Martens

Abel

Tag Closed Cup

Small Scale

Setaflash Series 3 Manual Flash Point Testers

Small scale flash point testers are universally specified in many international regulations to define and classify 'flammable' and 'combustible' substances. They provide the most precise and fastest means of carrying out flash point tests on a definitive 'flash' -'no flash' basis, both in the laboratory and the field. A 2ml sample size and 1minute test time for low temperature tests make these instruments ideally suited for many applications.
Petrochemicals, Biodiesel (FAME), adhesives, foods, flavors, cosmetics, paints/varnishes, waste, pharmaceuticals, polishes and aerosols are just some of the products routinely tested.

Active Cool is the latest instrument in the Setaflash Series 3 range. It has been designed to rapidly and efficiently carry out Flash / No Flash tests and to determine the flash point of liquids and semi-solids in the 10 to 130°C (50 to 266°F) temperature range.
When used in Ramp mode the temperature of the sample increases at a rate of 2°C/min. An audible prompt to carry out a flash test occurs every 1°C rise up to 100°C (every 2°C rise above 100°C), until a flash is detected, allowing rapid determination of a flash point in accordance with ASTM D7236 and IP 534.

Series 3 Catalog Pages

Setaflash Series 8 Automatic Flash Point Testers

The Series 8 'ActiveCool' is an automated closed cup flash point tester with a temperature range of 10 to 130°C (50 to 266°F) with no external cooling. When connected to a suitable water supply, the range is extended down to -20°C (-4°F).
There are two modes of operation; Flash / No Flash and Ramp. The ramp mode increases the sample temperature at a rate of 2°C/min automatically dips the ignitor every 1°C up to 100°C (every 2°C above 100°C), until either a flash is detected or the end of test temperature is reached.

Series 8 Catalog Pages

Setavap 80000-0 RVP Analyzer

ASTM D5188; D5191; IP 394; IP 409; EN 13016-1; EN 13016-2 (37.8°C)

Correlates with: ASTM D323; D2533; D4953; D5482; D6378; IP 69; IP 402 (obs); ISO 3007; EN 12 (obs); JIS K2258;
NF M07-07

Setavap 2 Portable RVP Analyzer

ASTM D5191; IP 394; IP 409 (37.8°C); IP 481; EN 13016-1; EN 13016-2 (37.8°C)

Correlates with: D323; D4953; D5482; D6378; IP 69; IP 402 (obs); ISO3007; EN 12 (obs); JIS K2258; NF M07-079

17000 Series Penetrometers

Manual, Semi-Automatic and Fully Automatic Penetrometers, Cones, Needles, Kits, Plungers and water baths.
Also have manual and automatic grease workers.

ASTM D5; D217; D937; D1403; D1321; D1831; D2884; IP 49; IP 50; IP 179; IP 310; IP 376; BS 1377; BS 2000 Parts 49, 50, & 179; BS 2499 Part 3; EN 1426; ISO 2137; DIN 51 579; DIN 51 580; NF T60-119; NF T60-132; NF T60-140; NF T66-004;
JIS K2220

Copper and Silver Corrosion Testing

A range of stirred water or oil filled baths featuring digital temperature control to an accuracy ±0.1°C. All baths are manufactured from stainless steel and have a stainless steel top plate with multiple positions for test stations. Each position is equipped with a lid with an integral hook for suspending either a copper corrosion test vessel (Seta 11500-0) or a test tube support (Seta 11420-0).

A test tube support can hold up to three test tubes (Seta 11590-0). Any combination of copper corrosion vessels and test tube supports may be used. The Oxi-Cor can also accept up to three oxidation test vessels.

ASTM D130; D4048; D4814 Annex; IP 112; IP 154; IP 227 (obs); IP PM DJ 2005; BS 2000 Parts 112 & 154; DIN 51 811; EN 2160; FTM 791 5325; NF M07-015; JIS K251

2 Place and 9 Place Baths

Accessories for Copper and Silver Corrosion Tests

LPG Corrosion Test

11200-5 SETA RUST PREVENTION TEST BATH

ASTM D665; D3603; D5534; IP 135; BS 2000 Part 135; FTM 791 4011; ISO 7120; NF T60-151; JIS K2510; NACE TM0172-2001

Indicates the ability of steam turbine oils to prevent rusting of ferrous components, should water become mixed with the oil. Also used to test the corrosive properties of cargoes in petroleum product pipelines.

Rust Bath and Accessories

12200-3 SETA EXISTENT GUM SOLID BATH

ASTM D381-IP 131; IP 540; BS 2000 Part 131; BS 4348 (obs); ISO 6246; DIN 51 784; NF M07-004; FTM 791 3302; JIS K2261

A Solid Block Bath designed to carry out up to five simultaneous tests for determining existent gum content in fuels by the Jet Evaporation method

Gum Bath

15550-2 SETA OXI-COR BATH

ASTM D525; D873; D5304; IP 40; IP 138; BS 2000 Parts 40 and 138; ISO 2160; FTM 791 3352; FTM 791 3354; NF M07-012; NF M07-013; JIS K2276; Acccelerated Shelf Life Test for Dried Pet Food

Also suitable for CORROSION TESTS to: ASTM D130; D4048;D4814 Annex; IP 112; IP 154; IP 227 (obs); IP PM DJ 2005; BS 2000 Parts 112 and 154; DIN 51 811; EN 2160; FTM 791 5325; NF M07-015; JIS K2513

15550-2 Catalog Page

16120-2 SETACLEAN TOTAL SEDIMENT TESTER

ASTM D4870; IP 375; IP 390 (Procedure A); ISO 10307; BS 2000 Part 375; NF M07-063

A compact bench-mounted unit for determining the insoluble material content of distillate and residual fuel oils

Click here for catalog page

90000-2 SETA OIL TEST CENTRIFUGE

ASTM D91; D96 (obs); D893; D1290; D1796; D1966; D2273; D2709; D2711; D4007; D5546; IP 75 (obs); IP 359; BS 2882 (obs); ISO 3734; ISO 9030; FTM 791: Methods 3000; 3003; 3004; 3101; 3121; 5661; DIN 51 793; NF M07-020; API 2542; API 2548; API MPMS Chapter 10.3

Seta Oil Test Centrifuge is a microprocessor controlled, heated
centrifuge manufactured exclusively for Seta by Hermle Labortechnik.
The instrument is fully programmable allowing automatic configuration to the specified oil test parameters.

Check the catalog pages for details on individual methods

Setafuge Hazard Reduction System and Accessory Chart

91600-0 SETA MFT MULTI FILTRATION TESTER

ASTM D2068; IP 387 (Procedures A, B & C); Correlates with ASTM D6426

The Seta Multi Filtration Tester is a unique and flexible instrument designed to test distillate fuels including gas oil, gas turbine fuel,
kerosene, diesel, biodiesel and biodiesel blends. It is the only tester that performs both existing IP 387/D2068 and D6426 methods, and offers the possibility of testing other types of fuel and adopting future filtration and filterability test procedures.

The MFT is also being used in the quality control process of Biodiesel production by many producers, often in conjunction with the "cold soak test".

Catalog page for MFT

19400-4 SETA ROLL STABILITY TESTER

ASTM D1831; MIL-G-10924

The Seta Roll Stability Tester simulates the effect of squeezing grease between the rollers and the outer race of a roller bearing.
Up to four test cylinders, each containing a heavy roller, is loaded with the sample grease and placed horizontally upon a set of drive wheels that rotate the cylinders at either 10 or 165 rev/min. A digitally controlled fan assisted air bath provides evenly distributed heating up to 150°C, and an integral timer is used to set the test duration.

19400-4 Catalog Page

16160-2 SSAFCON Sampler

ASTM D2276; D3830 (obs); IP 216; FTM 791 3008

Click here for catalog page.

99700-3 SALT-IN-CRUDE ANALYZER

ASTM D3230; IP 265

A portable instrument that measures conductivity and temperature of crude oils

Catalog Page for 99700-3